Exactly How To Install A Bath Tub (For Beginners).
Exactly How To Install A Bath Tub (For Beginners).
Blog Article
The content listed below involving How to Install a Bathtub is exceedingly insightful. Don't miss it.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the project can move easily; if you have to open a wall to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the new one. Ensure you have certified on your own for the work and also are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you may require an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water supply pipes.
Your tools as well as material checklist should comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite bothersome due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using both wood boards under its feet, place the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has been utilized at least once as this will settle it right into its last setting.
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on How to Install a Bathtub. Thanks a ton for spending some time to read our piece of content. Liked our content? Please share it. Let other people check it out. Thanks so much for going through it.
Call Us Now Report this page